There is a common misconception that just pressure washing a deck prior to staining is all you need to do in order to prep your deck for stain. Pressure washing can help, but if you want your stain to last, using a good deck cleaner and brightener on the deck prior to pressure washing will provide you the best result.

Do I need to wash my deck before staining?

Is Deck Cleaner Necessary Before Staining My Deck? In short, yes. It is highly recommended to use a deck cleaner when prepping your deck for a new coat of deck stain. Also, recommended but not required is the use of a deck brightener before staining your deck.

How long can you wait to stain a deck after power washing?

After a deck has been power washed it will have some retained moisture within the wood. It’s important to let the wood dry thoroughly so none of the water that soaked into the wood gets trapped under the stain. In perfect drying conditions, 48 hours is enough for the wood to get to where it needs to be before staining.

What happens if I don't power wash my deck before staining?

If you decide not to power wash beforehand, not only will your new paint not stay for very long, but your old paint will still be underneath. Pressure washing will not only remove the dirt and grime, but it can also remove old, chipped paint that may cause discrepancies in you new paint job.

How do you prepare pressure treated wood for staining?

Wash the Wood Allow it to dry before staining. Wash the pressure-treated wood with a deck cleaner, scrubbing the wood surface with a brush while wet. Use a pressure washer if the wood has tough stains. Allow the wet cleaner to soak into the wood for about 10 minutes or to manufacturer’s directions.

What happens if you stain a dirty deck?

When a deck stain is applied over an old failing stain it will start flaking and peeling within a year or so making an even bigger mess. After the deck cleaning or deck stain stripping process, a wood deck brightener is then needed. This “brightens” the wood while restoring back to the proper pH level.

Do I need to clean my deck before sealing?

Applying Deck Sealer to a Wood Deck. To get the most effective seal possible, thoroughly clean your deck before applying the sealer. Be sure all debris, dust, grime and mildew is removed. Check out our step-by-step guide for the best ways to clean a deck or pressure wash a deck.

Can you pressure wash and stain a deck in the same day?

DPI Pressure Washing recommends you wait 72 hours following cleaning to stain your deck. If it rains on one of the days afterwards, you’ll have to wait again, but it will be worth it.

Should you power wash a deck?

A pressure washer can clean a wood deck much faster than you can scrub it by hand. That is a terrific advantage. However, a pressure washer will frequently destroy the surface of the wood. … Those that are not eroded can be dislodged, leaving the wood fuzzy or rough after it dries.

How many coats of stain should you put on a deck?

The general rule of thumb is to apply only as much deck stain as the wood can absorb. Typically this will be 2 coats, unless your dealing with extremely dense hardwoods which may only be able to absorb 1 coat of wood stain.

Article first time published on

How many dry days do you need to stain a deck?

Depending on temperature and humidity, allow 24 – 48 hours of dry time before using your beautifully restored deck or porch.

Should a pressure-treated deck be stained?

Staining Treated Wood Not only can you stain treated wood, painting and staining pressure-treated wood is actually good for your new deck. Although the treated wood doesn’t need to be protected against rot, staining it will help reduce surface cracking.

What is the green stuff on pressure-treated wood?

Why is some treated wood green? The green color you see on treated wood is caused by chemical reactions that take place between the preservative components and the wood. Copper is still the most widely used element in wood preservatives and creates a green color on the wood.

Do you sand pressure-treated wood before staining?

All wood, except manufactured products like composite wood — even pressure-treated lumber — need to be sanded and stained. If you want it to last, you have to put in the time and some elbow grease.

Can I clean my deck with dish soap?

Liquid dish soap (ammonia-free) is safe for use on cleaning your deck when mixed with a little warm water. … Once you’ve blended your mixture, swab it on your deck and rinse it clean with water. Oxygen bleach or powdered oxygen laundry cleaner is safe for use on wood decks and useful in removing mold or spores.

How do I clean my deck without a pressure washer?

1. Add half a cup of baking soda to one gallon of water;
2. Mix in 1/8 of dish-washing detergent;
3. Spray on your concrete deck and allow it to sit for half an hour;
4. Scrub thoroughly and rinse with a hose.
5. Apply a coat of concrete sealer to protect your deck from future stains.

Do you need to apply a sealer after staining a deck?

Most of the time, stains also contain a protective sealant. It’s a good idea, though, to re-seal your deck (or check that it needs to be re-sealed) once a year. Water-based stains can adhere to water or oil-based coatings already present on the wooden surface.

Should I power wash my deck before sanding?

Splintered, cracking, or just plain rough wood should be sanded first, then pressure washed to open the wood’s pores and allow penetration of the stain. Deeply grooved wood that has mold, moss and other growing things filling the cracks will need treatment with a deck and siding cleaner.

Can you ruin a deck by pressure washing?

The impact of washing your decks under high pressure is profound in softer materials such as PVC. The pressure washer can significantly engrave the PVC on the deck if you use unreasonably high pressures during a routine washing exercise. Washing a composite deck under high pressure can also lead to extreme damages.

What kind of pressure washer do I need to clean my deck?

For cleaning a wooden deck, you’ll be best served by using the lowest pressure setting that’s still effective. For soft woods like cedar or pine, this is usually about 500 to 600 psi. For harder woods, it can go up to 1200 to 1500 psi. Choose the right tip to use as well.

Do you brush or roll stain on a deck?

You should use a roller brush or sprayer to apply a steady coat of quality stain, such as Olympic Elite stains or Olympic MAXIMUM stains. … PRO TIP: Back brushing your stain will help the stain soak into your deck boards, allowing better, long-lasting results.

Can you use a roller to stain a deck?

A paint roller can be used to roll stain on. … A wide 18-inch roller may work well for staining a few fence or deck boards at a time but a mop or stain pad will hold more stain lessening the amount of time you have to dip back into the stain bucket.

What is the best temperature for staining deck?

Apply stain only at the proper temperature. For most stains, 70 degrees Fahrenheit is the optimum, with the safety range from 50 to 90 degrees Fahrenheit. Stains do vary, so check the label first. Avoid high humidity and staining on hot surfaces.

Do I need to sand my deck after pressure washing?

Make sure your deck is thoroughly dry before you sand. If there has been recent rainfall or if you have power washed, wait several days before sanding.

Does stain get darker as it dries?

Apply a second coat of stain after the first has dried fully. This will usually produce a darker coloring, but it adds a step to the process and slows production. … Leave a dampness of stain on the wood that dries to a darker coloring.

What happens if you apply second coat of stain too soon?

If you apply a second, unnecessary coat of stain to wood that is already adequately covered, you risk creating a tacky surface that is prone to early peeling because the second coat is not penetrating the wood surface, but simply laying on top of the first coat of stain.

Can I apply a second coat of deck stain a week later?

Can I Apply a Second Coat of Stain a Week Later? No, applying a second coat of stain a week later is a bad idea. If you apply another coat of wood stain after a week, it will not adhere to the wood properly.

What is the best time of year to stain a deck?

The best time to stain your deck is either the spring or the fall. If you stain your deck in the summer, make sure you do it out of the direct sunlight. Applying a deck stain in direct sun will cause the stain to dry to quickly and can result in premature stain failure.

Why is my deck sticky after staining?

“A sticky or tacky deck is usually due to over-application or failing to wipe the excess stain from the surface of the wood. … Rinse thoroughly with a garden hose and spray nozzle, and let the wood dry. This removes any tackiness or residue.”

What if it rains the day after I stain my deck?

Splotchy Appearance If it rains within 48 hours after you apply the stain, the water will soak into the wood pores and try to displace the stain. This will result in a splotchy surface rather than an even tone. If it rains right after you apply the stain, the stain will peel and flake off.

What happens if you don't stain pressure-treated wood?

The effects that can occur due to a lack of treatment are aesthetic in nature. After 6 months, the wood will start to lose its color and will begin to fade. Ultimately it will fade to grey or silver. This is not a problem in and of itself, and some people prefer this look for their decks.