Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure. All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck.

Can you use too much Thompson Water Seal?

The sealant may also take longer to dry if you apply it in excess or if the surface already has a previous one coat of sealant on it. You may also notice tackiness on the sealed surface if you do not give sufficient drying time or if the weather is too cold to facilitate the drying process.

How long does Thompson's Water Seal take to cure?

Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity. Allow minimum of 30 days drying time before applying oil based paint over Thompson’s® WaterSeal® Waterproofing Wood Protector – Clear.

Can you apply two coats of Thompson's Water Seal?

Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.

Does Thompson Water Seal prevent mold?

Thompson’s® WaterSeal® Waterproofer Plus Clear Wood Protector is designed for all exterior wood and decking surfaces. This protection includes: Water repellency, prevents water damage, maintains natural wood grain, all while resisting mold growth.

Can Thompson Water seal go over stain?

Yes, you can put Thompson water sealer over stained wood whether the stain is water or oil-based. … If the stain has completely dried and cured it’s fine to apply sealer, but if there is still some moisture, applying the water seal over the stain might cause problems.

Why is my deck sticky after sealing?

“A sticky or tacky deck is usually due to over-application or failing to wipe the excess stain from the surface of the wood. … Rinse thoroughly with a garden hose and spray nozzle, and let the wood dry. This removes any tackiness or residue.”

When can you walk on Thompson Water seal?

Now that you’ve applied Thompson’s Water Seal following the instructions above, to your entire surface, you can walk away and let it dry for 24 hours. That’s all the time you need to let Thompson’s Water Seal work to protect your outdoor surfaces from water damage.

Can you put Thompson Water seal on treated wood?

Some, like Thompson’s® WaterSeal® Waterproofing Wood Protector, recommend waiting 30 days before application on new pressure treated lumber. Other products, like Thompson’s® WaterSeal® Waterproofing Stain, can be applied immediately to new pressure treated lumber.

How Much Thompson Water Seal do I need?

One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.

Article first time published on

How Much Thompson Water Seal do I need for my fence?

Divide the total square feet of fence to be stained by the coverage listed on the can. For example, if you have 1,000 square feet of fence and the stain says that 1 gallon covers 200 square feet, you would divide 1,000 by 200, which equals 5 gallons to cover the fence.

How long does Thompson's Water Seal Advanced last?

Thompson’s WaterSeal Wood Protector Apply a coat of this wood-protecting sealer with either a brush or a sprayer, and it will last up to 3 years before reapplication is necessary.

Can color be added to Thompson Water Seal?

Only one coat of Thompson’s® WaterSeal® Waterproofing Stain – Transparent is recommended. A second coat can be added if more color is desired. Allow the first coat to dry approximately 2 hours.

Why is my deck turning black?

The biggest reason for a deck stain turning black is mildew. All wood surfaces need to be cleaned correctly prior to staining. … Mildew can begin to grow underneath the deck stain, which causes discoloring. This can also lead to rot and decay because if there is mildew there is also moisture present.

How many coats of stain should you put on a deck?

The general rule of thumb is to apply only as much deck stain as the wood can absorb. Typically this will be 2 coats, unless your dealing with extremely dense hardwoods which may only be able to absorb 1 coat of wood stain.

Is it OK to stain deck before rain?

Applying Stain First, ensure the deck is completely dry. Remember, no rain 24 hours before you apply stain and no rain 24 hours after the staining project. Assuming the deck is dry and thirsty for stain, it’s time to make your deck amazing.

Can you apply Thompson's water seal in the rain?

Thompson’s Water Seal, offers superb weather protection for bricks, mortar, stone & concrete. Its advanced silicone micro emulsion soaks in deep to provide long lasting protection against rain damage.

Why is my Thompson water seal white?

If you have white spots in the concrete there is probably water under the water coat. Maybe if the sun dries it out and the white spots go away you could try applying another coat. I would have tried DRYLOK Latex Water Proofer on your patio, I use this product on my concrete steps.…

How long should you wait to water seal pressure treated wood?

Let it dry. Most deck sealers for PT lumber require 24 to 48 hours of drying time, so make sure there’s no rain in the forecast.

Is it OK to water seal pressure treated wood?

However, most pressure-treated wood should have periodic sealing against moisture, preferably every year or so. Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water.

How often should you stain pressure treated wood?

Many homeowners wonder, “How often should I stain my deck?” To keep a deck looking great and prolong the life of the wood, a deck should be stained every two to three years.

Can you apply Thompson's water Seal with a rag?

Use a dry microfiber cloth or rag to clean the surface. Keep in mind that using a damp microfiber cloth to clean the surface of an unfinished wood could warp. Add a drop of water on the surface to determine whether your wood is finished or unfinished. If it absorbs and leaves a mark, then it’s unfinished.

How often should you seal a wood fence?

While you should always follow the manufacturer’s recommendations, the general rule is that wood fences should be stained every five years and sealers should be applied every two to three.

Can I apply a second coat of stain a week later?

Can I Apply a Second Coat of Stain a Week Later? No, applying a second coat of stain a week later is a bad idea. If you apply another coat of wood stain after a week, it will not adhere to the wood properly. As a result, any finish you use on top will experience adhesion problems and peel off.

How much will a gallon of Thompson Water Seal cover?

That determines how many gallons of stain are required (each gallon covers up to 400 square feet). You can buy it and be on your way. Thanks to its pigment-suspension technology, there’s no need to wait for the Waterpoofing Stain to have its turn in the paint shaker.

Can you spray Thompson's Water Seal on a fence?

Treating the Fence For the convenience of a one-day project, Thompson’s® WaterSeal® Exterior Stains can be applied to damp, freshly cleaned wood. When treating your fence and applying a Thompson’s® WaterSeal® waterproofer or fence stain, follow the label’s application instructions carefully.

How many gallons does it take to seal a deck?

How Much Stain Do I Need For My Deck? For decks and patios that measure up to 175 square feet, you will only need one gallon of stain, in any transparency. If your deck or patio measures up to 550 square feet, you will need to buy 2 gallons of stain.

Is Thompson water Seal oil or water based?

Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.

Does Thompson water Seal come in quarts?

Thompson’s® WaterSeal® Clear Multi-Surface Waterproofer – 1 qt.

Is Olympic and Thompson's the same?

Olympic Waterguard is a clear coat. The Thompson’s WaterSeal line of products includes clear sealers, but also covers tinted stains/sealer combinations.

How long does Thompson deck stain last?

Thompson’s WaterSeal includes a complete line of deck sealers and stains for protecting deck wood from moisture and sunlight. Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure.